SMGBobbyScott
Friday, April 12, 2013 2:33:31 PM

check for spark... then spray about a half can of ether into the carb..... if it starts then it's a fuel problem.... 👍

DrafterX wrote:

If the motor turns over when you turn the key, then its not the battery. You should probably change the spark plug every year anyways. Half a can of ether is overkill, but a little will help you get started. I would try cleaning the air filter too...just take it out (it is probably foam rubber) and just rinse it out and squeeze the hell out of it).

I'm assuming that the oil is fine as well.

All other issues being normal, the motor should crank. If the motor isn't turning over at that age it is probably the battery.

Hope that helps.

daveincincy
Friday, April 12, 2013 2:34:58 PM
Oil? 🤔

[sarcasm]

DrafterX
Friday, April 12, 2013 2:35:34 PM
🤔

I wonder if there's an oil level sensor..?? 🤔

might explain the rocking thing.. 🤔

Gene363
Friday, April 12, 2013 2:45:08 PM

I don't know if this means anything, but when it started acting up last summer I found that rocking it back and forth while starting seemed to help...perhaps it was just coincidence that it started up regardless of the rocking. Seems odd that that would actually help at all. 🤔 ...but mowers these days have so many "safety" features that if anything has a bad connection (i.e. seat, parking brake, etc) it won't start.

daveincincy wrote:

Might be dirt in the fuel tank blocking the intake screen. The sloshing fuel might temporally move the debris and let it run.

Ilovetosmoke68
Friday, April 12, 2013 3:17:48 PM
Have you tried seafoam? You can add it either directly to the carb or you can add to fuel. It's a carb cleaner.
Abrignac
Friday, April 12, 2013 3:38:39 PM
Assuming your spark plug fires, switches are not corroded and control cables are not broken or froze then more than likely your carb is gummed up.

Most push mowers, weed eaters, blowers, etc. don't have fuel shut off valves. As such when not running an amount of gasoline sits in the carburetor. Over the months it breaks down and forms a gummy varnish. This varnish will thicken and clog the tiny passageways in small engine carbs. It will also lock small moving parts in place.

The cost to due a carb job is in some cases is 50-75% of purchase price. If possible, you may want to drain the gas between uses or if unable try to run it out of gas between uses.

jwweod
Friday, April 12, 2013 5:30:23 PM
don't know if anyone has mentioned it but it could be fuel related.

[sarcasm]

Abrignac
Friday, April 12, 2013 5:37:41 PM

don't know if anyone has mentioned it but it could be fuel related.

[sarcasm]

jwweod wrote:

](*,) 😣 😣

Numismaniac
Friday, April 12, 2013 5:59:15 PM

[size=6][color=darkblue]Checking the Ignition System(Fire)

The easiest way* to check for a spark is to remove the spark plug from the engine and then reattach the spark plug wire to the spark plug. When you remove the spark plug, check to make sure the spark plug is not dirty or too worn, as this can cause problems.

Next, position the spark plug so that the end of the spark plug makes contact with a piece of grounded metal on the engine.The spark plug should be positioned close to the grounded piece of metal and should be away from the engine.

When you turn over the engine, either by pulling the pull cord or activating the electric starter, you should be able to see a spark jump from the spark plug to the grounded metal. The spark is visible and typically looks bluish in color.

Gene363 wrote:

[-x

Here's how my Grandpa found out.

As a youngster my Grandfather always had me grab the spark plug while he turned the crankshaft, saying "See if it'll fire, Son" Naturally not wanting to disappoint, I learned to take a pretty good jolt, hehe!

I once saw him "Kill/Ground out the motor" on an old tricycle front end AC tractor, 4 cyl, by grabbing two of the plug covers and grounding it out, that's how he proved to my Dad that one of the other wires had a short, and was touching!!!

HEHE, new wires, no more "miss".

He could not read or write, never went to school, could sign his name only, but could fix anything that had a motor or engine, regardless of type, from Steam Donkeys on up to combustion, and large diesels

sr20vet
Friday, April 12, 2013 9:56:13 PM
I would absolutely NOT run water through the air filter. Water is not compressible. Get a bit of moisture in your combustion chamber and it'll run like crap, get a bit more and you'll blow your motor. Blow 'em out with an air hose, re-oil 'em if they're oiled filters, that's it. If that's not enough pony up the few bucks for a new one.

As for the safety switches I see no reason not to bypass them, or replace them with something a little less sensitive if they're a problem. If not leave them be. Lots of people loose toes on mowers. There is no reason you should have your blades engaged when you're not in the seat anyways.

The spark plug trick works but be careful once again. I doubt your mower has anything sensitive enough to be adversely affected by the power surges but it's possible. Don't do it long, just a quick peek, and then give the gas a few minutes to evaporate out of the combustion chamber before replacing the plug.

wheelrite
Saturday, April 13, 2013 9:25:52 AM
it's the ethanol in the gas,,,