victor808
Wednesday, January 4, 2006 4:26:00 PM
So, stupid question, but I was wondering if anyone else has run across this issue.

I was trying to calibrate my hygrometer today (I was getting some high readings and thought I should get a good bead on where the actual humidity was at) so I tried the salt method. I put my hygrometer in a small tupperware container for a few hours with a soda cap full of salt and a little water (not enough to be a slurry).

When I checked this evening the hygrometer read 90! I was told that salt/water solution was at 75% humidity. Is it possible that my hygrometer is off by 15 points, or did I do something wrong? Should I be getting a new hygrometer (I don't see any screw on this one for calibration)?

jupiter33458
Wednesday, January 4, 2006 4:33:00 PM
Problem Solved... go Digital.

Don't wast time calibrating.

** edited due to competitor reference

xrundog
Wednesday, January 4, 2006 4:35:00 PM
Dial type? Usually you can remove the back. What you do is rotate the face until the needle lines up at the right number. 15 points is very possible. They often aren't calibrated. They stick sometimes too. Digital is better. If it IS digital 15% is a lot. Most don't have an adjustment (I've done alot of looking).
xXxHOSSxXx
Wednesday, January 4, 2006 4:39:00 PM
If it doesn't adjust and you don't want to buy a digital, take note of how far off it is and add/sub the appropriate amt from all future readings. I have several, one is digital, the rest are analog. I think the worst one i have is off by 12%. So i just wrote +12% on it and that does the trick.
cigarhusker
Wednesday, January 4, 2006 4:42:00 PM
Victor108,

This has all been very well covered before. Try this for starters:

http://www.cigarbid.com/auction/forum/forum.cfm?action=list&forumID=1&messageDisplay=0000000048754 

Comp12458
Wednesday, January 4, 2006 4:48:00 PM
I am new to these parts, but in my limited experience with hygrometers, I have foudn that when you do teh salt/H2O treatment, you need to leave it in there for atleast 8 hours, and I also double zip lock bag it to make sure you keep a good tight seal! Also, digital Hygrometers often need calibration also unless stated "Pre Calibrated"
rodehog56
Wednesday, January 4, 2006 5:54:00 PM
The best solution- Take a large heavy object in hand raise above head and strike with a downward motion on to the hygrometer and smash until you can not tell what it is.

throw out any open window(close window).

Smoke favorite ciagr.

rodehog56
Wednesday, January 4, 2006 5:54:00 PM
PS. this will calibrate any hygrometer perfectly! LOL
victor808
Wednesday, January 4, 2006 6:11:00 PM
I have considered it... but that would leave a big hole in my humidor. Cant have that, and duct tape doesn't look nice... so no smashing it for me.
rodehog56
Thursday, January 5, 2006 2:30:00 AM
Sorry, remove hygrometer from humidor first, place on stable flat object. Most are held by velcro.

I have a hygrometer tree growing in my backyard from all the ones I have tossed out the open window.

Looks kinda nice.

Slimboli
Thursday, January 5, 2006 2:47:00 AM
A few hours is not enough ... it's got to be six to eight !!!
victor808
Thursday, January 5, 2006 8:43:00 AM
yeah... I think I used too small a tupperware container. I left it overnight and it kept reading 90%. But in the humidor w/ some crystal/gel humidification disc (which should hold 70-72) I get a reading of about 68. One of the two environments is not being read correctly (since there should only be about a 5% difference between the two.

Still am considering smashing it with a hammer...

rodehog56
Thursday, January 5, 2006 5:07:00 PM
It's the only thing that works! LOL