JadeRose
Wednesday, February 22, 2012 9:45:44 AM
I'm trying to get my old truck (1968 Ford 360 2 barrel) started after sitting all winter. I can get it to fire if I use starting fluid or prime with gas but I cannot get gas to flow. Fuel pump is fairly new and seems to be working. Any ideas?

](*,) 😣 😣 🙏 🙏 🙏

Northsidepk
Wednesday, February 22, 2012 9:53:12 AM
Fuel Filter maybe, Im not all that familiar with your make or model but many carborated motors had the filter screw into the carb itself, right off the fuel line.

Otherwise, are you sure its a fuel problem, could be spark or air. Hey a bird could have nested in your air filter assembly!!!

Oh, bad/old gas could be another, depending on how cold it is in your area it could be vapor locked as well. Just have to heat up your garage for a bit to fix that.

JadeRose
Wednesday, February 22, 2012 10:02:02 AM
Our winter has been pretty mild. I also poured some Sea Foam in the gas when I parked it in October. The Fuel filter is hose mounted and is spotless, although I'm going to change it anyway. If I use Starter fluid or prime the crab with gas, it starts for a bit.
Northsidepk
Wednesday, February 22, 2012 10:04:18 AM

Our winter has been pretty mild. I also poured some Sea Foam in the gas when I parked it in October. The Fuel filter is hose mounted and is spotless, although I'm going to change it anyway. If I use Starter fluid or prime the crab with gas, it starts for a bit.

JadeRose wrote:

Jets gummed up?

is the gas cap on? Must have back pressure

JadeRose
Wednesday, February 22, 2012 10:07:06 AM

Jets gummed up?

is the gas cap on? Must have back pressure

Northsidepk wrote:

Cleaned with carb cleaner. Good thought on the gas cap. I'll check the seal on that.

Rclay
Wednesday, February 22, 2012 10:23:24 AM
Some one pooped in your gas tank.
ZRX1200
Wednesday, February 22, 2012 10:38:56 AM
Fuel filter on a 68 ford 360 should be inline not screw in.....last time I bought one 1996 it was 2$.

Pull the plugs and check the points. Could also be the ethanol fuel too though I doubt that.

BuckyB93
Wednesday, February 22, 2012 11:38:27 AM
Have you checked the 710 cap?
streetrod
Wednesday, February 22, 2012 11:43:22 AM
If the gas is not flowing as you said, find out where the stopage is. First disconnect the fuel line to the filter and place the filter end of the fuel line in a bottle. Crank the motor over it should pump gas in to the bottle. If not, either the fuel tank screen, fuel pump or fuel line is bad or clogged. If thats ok, rehook hose up and repeat process at every point where you can diconnect line up to the carb. If it is all clear to the carb, then the carb is the problem. If it starts with starting fluid or by priming carb, I don't think it's the points or plugs. Just my humble opinion.
JadeRose
Wednesday, February 22, 2012 11:45:00 AM
The fuel lines were locked up tighter than a drum. I pulled off the feeder line to the pump and put it back on. Then I turned the ignition over and watched the fuel filter fill back up and the truck fired right off. SUCCESS. Northsidepk guessed it....vapor lock.
tailgater
Wednesday, February 22, 2012 11:46:32 AM

Have you checked the 710 cap?

BuckyB93 wrote:

Blonde?

JadeRose
Wednesday, February 22, 2012 11:47:35 AM
Thanks for all the replies. i haven't done engine work in over 20 years and am veeeery rusty. I bought this old truck to play with and to me, this is all fun. Thanks again.
HockeyDad
Wednesday, February 22, 2012 11:52:57 AM

I'm trying to get my old truck (1968 Ford 360 2 barrel) started after sitting all winter. I can get it to fire if I use starting fluid or prime with gas but I cannot get gas to flow. Fuel pump is fairly new and seems to be working. Any ideas?

](*,) 😣 😣 🙏 🙏 🙏

JadeRose wrote:

It's all ball bearings nowadays. Also, prepare that Fetzer valve with some 3-in-1 oil.

ZRX1200
Wednesday, February 22, 2012 11:57:01 AM
Easy motor to work on. Weak link is the oil gear from the distributor to the oil pump.
Thunder.Gerbil
Wednesday, February 22, 2012 12:03:41 PM
Have you checked the tie-rod guards?
JadeRose
Wednesday, February 22, 2012 12:28:26 PM

Have you checked the tie-rod guards?

Thunder.Gerbil wrote:

I did a data dump from the tie rod guards and found them to be functioning normally. I think I will upgrade the chip in them, though.

HockeyDad
Wednesday, February 22, 2012 12:37:07 PM

I did a data dump from the tie rod guards and found them to be functioning normally. I think I will upgrade the chip in them, though.

JadeRose wrote:

That will get you something like 20 more horsepower.

BuckyB93
Wednesday, February 22, 2012 1:10:38 PM

The fuel lines were locked up tighter than a drum. I pulled off the feeder line to the pump and put it back on. Then I turned the ignition over and watched the fuel filter fill back up and the truck fired right off. SUCCESS. Northsidepk guessed it....vapor lock.

JadeRose wrote:

Damn! I never win any of these contests.

JadeRose
Wednesday, February 22, 2012 1:24:33 PM

Damn! I never win any of these contests.

BuckyB93 wrote:

Well...thanks for playing anyway, Bucky. You won't go away empty handed though!! You'll receive fabulous parting gifts!!! Rice-A-Roni and a case of Turtle Wax!!!

BuckyB93
Wednesday, February 22, 2012 1:35:14 PM
I don't even own a turtle in which to wax. The Rice-A-Roni might come in handy though. Thanks.