greenxeyezz
Thursday, September 21, 2006 4:21:00 PM
Okay I purchased the 4oz tube. Do i put the tube in the humidor? Do i pull off the ends to hydrate it? Or do i put it in another bowl or what not? do i just spray the outside?

the lack of precise instructions for this "tube" make it hard. it just gives instructions for "loose" beads.

ANY HELP PLEASE?

Whistlebritches
Thursday, September 21, 2006 4:57:00 PM
Hang it in the bowl on the back of the toilet and like magic you will be perfectly humidified every visit.

Honestly I use loose beads in pantyhose.I spray them with distilled water.Not sure bout the tubes.

Ron

greenxeyezz
Thursday, September 21, 2006 9:45:00 PM
anyone? i opened up the ends and they kinda spilt out (10 beads) will putting water on/in them make them expand? how does the humidity escape from the tube? is the clear part partially able to transfer the humidity?

any help please?!

tpottiger
Thursday, September 21, 2006 9:52:00 PM
They should be partially clear & partially cloudy... This will allow them to absorb & release moisture as needed.

You can spray it, soak it, or pour water directly on them, it all works out in the end. Just don't over soak them. (see above...)

If the beads didn't get dirty, I would just put them back in!

tpottiger
Thursday, September 21, 2006 9:54:00 PM
Dang, forgot one thing!

The "H" beads don't expand.

(Although I have not tested this theory in the microwave, I have found that most things will expand in the microwave if you let them in long enough!)

greenxeyezz
Thursday, September 21, 2006 10:07:00 PM
so then the question still remains, do i hydrate them in the tubes, and the tubes work to release the rh, or is that just the "canister" they came in? and i have to move them somewhere else?
BikerBob1961
Thursday, September 21, 2006 10:09:00 PM
I sent an email to find out the info and included the addy for this post. If he sends me the info I will post it here as soon as I get it. I think you might just leave the beads in the tube and place the tube in a bowl of distilled water for a couple seconds till about 65% of them turn clear. The tube itself should let the water to pass through. The beads don't expand just turn clear when charged.
greenxeyezz
Thursday, September 21, 2006 10:14:00 PM
thanks for that bob, the instructions do say 5 teaspoons, however when i looked at the beads, some were clear some where white. clear means no water white means water in them right?
Pufferbelle
Thursday, September 21, 2006 10:24:00 PM
green, actually, clear means moistened and cloudy means dry. I would gently remove one end and using an eyedropper or medicine syring drop some DISTILLED water onto the beads. I found that when I followed the sites water amount, it was too much, so I would halve it and add more in a few days if the humidor doesn't read what it should.

HTH

Suzi

Open it over a clean paper towel and any that spill out are easily put back in. using the paper towel as a "scoop" as it were.

greenxeyezz
Thursday, September 21, 2006 11:41:00 PM
thank you again for all the information. I am going to put it in the cooler as it were, let it "season" overnight and see the RH reading. I want it to be at 65% about (already taking into account the deviation). So if its reading low ...ie 50%, i ADD distilled water correct? and if its reading high...ie 70%, i err....let it dry! lol.

Also does it matter if its on the bottom or the top of the cooler?

trying to maximize space in the cooler, so i was going to attach it to the top lid (along with the hygrometer) so that i have maximized the full space of the cooler.?

Pufferbelle
Thursday, September 21, 2006 11:59:00 PM
I don't think it matters where the tube is as long as the air can circulate around it. Depending on the size of your coolerdor, you might end up needing another one.

If the humidity reads low, the beads need a bit more distilled water. If it reads high, the beads need to dry a bit. You can try a hairdryer on low and not too close to the beads (or they'll perhaps break), to dry them up a bit. My guess is you'll need to add a bit of water. I am assuming this is the 4 oz humitube?

HTH

Suzi

greenxeyezz
Friday, September 22, 2006 12:26:00 AM
yep 4 oz humi tube, is 65% rh good enough? i think im going to construct the device to hold it to the top lid or maybe velcro lol....
bs_kwaj
Friday, September 22, 2006 1:05:00 AM
I bought some of those tudes and I think they suck.

I poured the beads out into some little plastic cartridge trays from a HP 1200 printer. They seem to work much better opened up that way.

Just my $.02...

blackdog2000
Friday, September 22, 2006 4:30:00 AM
The porous cylindrical cartridges they come in seem to be perfect. I don't think they need to be on the lid; anywhere will work.
Viper139
Friday, September 22, 2006 6:09:00 AM
The easiest way I have found to hydrate the beads is to lay the tube on a dish and spray the tube with distilled water, let the tube sit for a few minutes then wipe the excess water off of the tube itself. Add enough distilled water to make 65-70% of the beads clear and the rest opaque to white, this wil give the beads the ability to absorb excess moisture that gets into the humidor.

You can place the tube anywhee in the humidor, it does not have to be in any particular position in the humidor.

TROY6311
Friday, September 22, 2006 8:53:00 AM
Seems like alot of different solutions for using these tubes. I use them in a 55 gal coolerdor. Take the caps off and add water using a dropper. Leave some of the beads dry/cloudy. I use two in the coolerdor - one on the bottom and one towards the middle with an oust fan to circulate the air. Seems to hold rh at 65-70. everything in the cooler smokes fine.