dunkaroos
Monday, January 21, 2008 11:55:00 AM
I've been putting off doing my basement until the wife told me when it's finished, I can smoke down there.

So now my first order of business is to re-do the stair treads. We ripped up the carpeting and some stairs were damaged/broken. It appears that the risers are ok, but all the treads need to be replaced especially since we are going without carpet from here on out.

Basically, I'm no home improvement guru. Actually, I'm borderline inept, when it comes to these things. Can anyone offer some helpful hints or advise on getting started or what to avoid during the process.

daveincincy
Monday, January 21, 2008 11:56:00 AM
make it a slide.
dunkaroos
Monday, January 21, 2008 11:57:00 AM
^Ha LOL! That would be fun trying to get back up.
wacman7
Monday, January 21, 2008 12:01:00 PM
^ or a fireman's pole.

I realize you might note that getting back up will be more difficult, but if your wife is going to let you smoke down there, why do you need to come up? Put it in a closet with the latch tied back to a secret button on your desktop bust of Churchill...

na-na-na-na-na-na-na-na-na-na-na-na-na-na-na-na

Cigarman...

usahog
Monday, January 21, 2008 12:04:00 PM
before you rip out the old broken boards.. measure your risers hights and treads depths and cut accordingly for replacements...

also if your going to add possibly a hardwood flooring over the rough construction Treads and risers.. I'd go with something 3/8" thick or less.. many big boxes carry laminate hardwood floorings that will accommodate you..

Hog

Oh and a portable table saw or a local school woodshop would come in handy for you ;0)

daveincincy
Monday, January 21, 2008 12:08:00 PM
I was thinking more in line with something you'd see on Scooby Doo. Stairs/slide with the flip of a switch.
dunkaroos
Monday, January 21, 2008 12:16:00 PM
Re: 5

Thanks Hog. I bought replacement treads at the Depot. They are fairly thick, not sure exact thickness. I was planning on keeping the risers and ripping up the treads.

wacman7
Monday, January 21, 2008 12:21:00 PM
On a slightly more serious note than the fireman's pole...

You might think about putting something on the tread to give you a little better traction. My experience with basement steps is that they tend to be steep and can get a little slippery, what with the moisture during the warmer months of the year. Just throwing that out there for thought...

dunkaroos
Monday, January 21, 2008 12:22:00 PM
I've managed to borrow the required saw's, I think. Just casually searching the internet home inprovement sites for miscellaneous things I might need.
usahog
Monday, January 21, 2008 12:58:00 PM
check craigslist in your area.. "tools"

also you might want to add bracing (while you have the old treads removed) if your steps have had any bounce to them at all over the years?

Hog

kdotline
Monday, January 21, 2008 1:17:00 PM
don't know how old the house is, but look close to make sure the old treads are installed between the skirtboards (usually a piece of 2x nailed to the stringers), and not routed into the skirtboards (common in prefab stairs). These are a biatch to take out and the new tread never seems to cover the old gaps completely.
usahog
Monday, January 21, 2008 3:04:00 PM
^ what Kdot said above also.. I did not consider this at first thought...

if this be the case you may consider tying in new stringers.. much less headache...

Hog

andytv
Monday, January 21, 2008 4:48:00 PM
I'd suggest using adhesive in addition to nails/screws when replacing the boards......less squeaking.
sw48362
Monday, January 21, 2008 5:12:00 PM