dkeage
  • dkeage
  • Herf-A-Holic Topic Starter
Friday, August 4, 2006 5:17:00 PM
Frickin screws fell out on one of the hinges...............What is the best way to put screws into wood...........Thanks, AH
donsnyderiii
Friday, August 4, 2006 5:33:00 PM
Drill out the hole (a little larger than the outside/larger diamiter of the screw threads) insert a piece of dowel smeared with wood glue, let it set, pre-drill a new hole (into the dowell) slightly smaller than the smallest diameter of the screw and screw it on in.
donsnyderiii
Friday, August 4, 2006 5:34:00 PM
oh...and this belongs in the Mics. thread.
dkeage
  • dkeage
  • Herf-A-Holic Topic Starter
Friday, August 4, 2006 6:37:00 PM
Author: donsnyderiii

Thanks............

And if a Humidor is not Cigars and related, then I'm VERY sorry............

lofty1
Saturday, August 5, 2006 5:38:00 AM
a dowel is a good idea, but i usually just use toothpicks and wood glue. it works really well. you just stuff the hole with toothpicks smeared with wood glue. wait until it dries, and you're ready. it's not always easy to get a dowel that fits just right.
dkeage
  • dkeage
  • Herf-A-Holic Topic Starter
Saturday, August 5, 2006 9:07:00 AM
Thanks Lofty......
Whistlebritches
Saturday, August 5, 2006 12:27:00 PM
dkeage,

Lofty is dead on.BTW so are you,this is a C&R topic.

Ron

dkeage
  • dkeage
  • Herf-A-Holic Topic Starter
Saturday, August 5, 2006 2:42:00 PM
Using an off-shoot of Lofty's suggestion.......dude at Lowes suggested Wood Filler, instead of Glue........Letting it dry overnite, and will put the screws to it in the morning.......

Thanks guys....

C&R

JHC
  • JHC
  • Herf-A-Holic
Saturday, August 5, 2006 3:46:00 PM
Toothpicks and wood glue has always worked for me.
TBWCW
Sunday, August 6, 2006 9:53:00 AM
I had the exact same problem with mine. Used toothpicks and wood glue and haven't had a problem since. It even survived being shipped to Fiji.
dkeage
  • dkeage
  • Herf-A-Holic Topic Starter
Sunday, August 6, 2006 10:23:00 AM
Fixed it today.........works great!

Thanks for the input

usahog
Sunday, August 6, 2006 11:05:00 AM
I just seen this post... if/when you need to do this again.. use two parts apoxy resin... and again fill the holes allow it to set up at least 12 hrs.. then drill them out and apply the screws.. the apoxy will last longer and stronger then the wood filler

Hog

dkeage
  • dkeage
  • Herf-A-Holic Topic Starter
Sunday, August 6, 2006 11:11:00 AM
Thanks Hog, I'm hoping it doesn't happen again, but if it does I'll give that a try. I was pleasantly surprised by how hard the filler dried.......I let it sit for about 14hrs.

Gandalf
Sunday, August 6, 2006 11:41:00 AM
Another quick (but permanent) fix is to place a small drop of Gorrilla Glue in the hole(s) and gently reset the screw(s). Support the door to reduce any stress for 24 hours and it should be as good as new. Don't over do the glue though, as it is polyurethane based and expands during curing (almost like a foam).

They don't call it Gorrilla Glue for nothing - stuff is amazingly strong and will bond to just about anything. Don't get it on your clothes either as it will never come off.....

Just my 2 cents.......

dkeage
  • dkeage
  • Herf-A-Holic Topic Starter
Sunday, August 6, 2006 11:45:00 AM
Thanks Gan........how's your son and his school selection?
Gandalf
Sunday, August 6, 2006 12:07:00 PM
School's tempoarily on hold while he does an internship at a studio in R.I.

Not sure where it's going at this point. Thanks for asking.

How's things in your studio these days?

donsnyderiii
Monday, August 7, 2006 5:20:00 PM
Ooops...Sorry bout that. I'm a retard. You are correct in placing that in this forum. Drinking and posting, or in this case drinking and replying is not the smartest way to go...lol.