Nutttttttttty
Monday, December 4, 2006 7:04:00 AM
I guess I am just stupid or haven't thought about it long enough but can anyone tell me what the reason is for having different pronged electrical outlets all over the world. This is something I would figure would make alot of sense to have universal?
andytv
Monday, December 4, 2006 7:16:00 AM
from Wikipedia.......

There are two basic standards for voltage and frequency in the world. One is the North American standard of 110-120 volts at 60 Hz, which uses plugs A and B, and the other is the European standard of 220-240 volts at 50 Hz, which uses plugs C through M. The differences arose for historical reasons.

In the United States, Thomas Edison, the inventor of the first practical electric light bulb, insisted on using 110 volts direct current (DC) rather than alternating current (AC) for his electric system in New York City. However, George Westinghouse, who built the first large hydro-electric plants at Niagara Falls, decided to use AC instead of DC because it could be stepped up or stepped down in voltage using transformers. The electrical genius Nicola Tesla advised him that 240 V at 60 Hz was optimum, but authorities would not let him use more than 110 V for distribution. Eventually Edison switched his 110 V DC system over to AC as well, and so 110 V at 60 Hz became the American electrical standard, despite the fact it required conductors twice as large to carry the same amount of power as 240 V.

In Europe, the German company AEG built the first generating facilities, and chose 50 Hz because it fit better into the metric system of powers of ten (1, 10, 100). Unfortunately, 50 Hz is less efficient than 60 Hz because generators are 20% less efficient and transformers must be 30% bigger to step the voltage up and down. However, AEG had a virtual monopoly in Europe so their standard spread to the rest of the continent and eventually to Britain. Originally Europe was electrified at 110-120 V like North America, but after World War II, regulators decided to increase it to 220-240 V to reduce the amount of copper used for wiring.

American regulators would have liked to double the voltage as well, but there were far more household electrical appliances than in Europe. They compromised by adopting a split phase 240 V system, supplying 120 V on two live conductors going into each household with a single neutral. Small appliances ran on 120 V, big ones on 240 V. It was more complicated but saved copper and was backward-compatible with existing appliances. The original plugs could be used with the system, as well.

engletl
Monday, December 4, 2006 7:17:00 AM
Simple answer is the fact that not every country uses the same voltage/amperage for power...ie The USA is a 110vac system most every where else is on some variation of 220-240vac. A 110vac hairdryer doesn't like 220vac...so there are different plugs based on the voltage.

Todd

Nutttttttttty
Monday, December 4, 2006 7:32:00 AM
Thanks Andy
teedubbya
Monday, December 4, 2006 7:34:00 AM
It would also be easier if we used the same measurement systems, money, etc
blackfoot11
Monday, December 4, 2006 5:51:00 PM
Mr. TV is so smart.

if i could be anybody, i'd be just like him.

Eddie (aka Andy)

adroomi
Monday, December 4, 2006 6:07:00 PM
Nutttttttttty,

Thailand, like Japan and China use "type A" outlets as you do in the USA. However they are on a 220 volt system.

A couple of years ago, my brother came to visit me on Koh Samui Island.

He plopped down on the sofa, and before I could stop him, plugged his BRAND NEW (less than a month old) cell phone into the wall to charge it. It melted.

Does that offer a bit of an answer about "why?"

:)

dadz
Monday, December 4, 2006 6:13:00 PM
Nutttttttttty

What you meant to say was, not the "different pronged things around the world", but the difference in voltage and amperage values. You can get converters for any "prong" difference, but if the voltage is wacko, you're out a shaver or hair drier, thingo.

RICKAMAVEN
Monday, December 4, 2006 6:57:00 PM
teedubbya

if we used meters i would only be 1.524 meters short.

on the other hand if we used kilos 1 would only weigh 99.7903214. kilos.

i'd be short and thin instead of short and fat.